# C-Channel

> A C-channel is a steel section with a flat web and two flanges on one side. How sizes are written, C vs MC vs PFC, how channels behave and where they're used.

- URL: https://essential.construction/academy/glossary/c-channel/
- Author: Kyle Parry (https://essential.construction/about-us/kyle-parry/, https://www.linkedin.com/in/kyleparry/) - Kyle Parry is the founder of Essential Construction. He has worked in construction for more than 20 years, leading projects across Canada for the country's largest contractors and developers.
- Publisher: Essential Construction (https://essential.construction/)
- Last updated: 2026-11-03

---

A **C-channel** is a structural steel section shaped like the letter C, with a flat back (web) and two flanges on one side. Because one face is flat, C-channels are used where a member needs to sit flush against a wall or another member, such as lintels, stair stringers, bracing and framing.

## Types and how sizes are written

| Type | Example designation | Notes |
| --- | --- | --- |
| C shape (American Standard Channel) | C8x11.5 | 8 in nominal depth, 11.5 lb per ft; inside flange faces taper |
| MC shape (miscellaneous channel) | MC8x20 | Different flange proportions from a C of the same depth |
| Canadian metric channel | C200x17 | 200 mm nominal depth, 17 kg per m |
| Parallel flange channel (UK) | PFC 200x90x30 | Depth x flange width (mm) x kg per m; parallel flanges |
| Cold-formed C section | Lipped C stud or purlin | Light gauge, often with stiffening lips |

In the US, hot-rolled C and MC channels are now most commonly available in ASTM A992, though some smaller channels may only be available in ASTM A36. Strut channel (the slotted channel used for pipe and conduit supports) and cold-rolled channel in ceilings share the name but are not structural shapes.

## How C-channels behave

- **Twisting:** a channel's shear centre sits outside the web, so a load applied through the web tends to twist it. Engineers handle this with bracing, by pairing channels back to back, or by loading close to the shear centre.
- **Weak axis:** the narrow flanges make it much weaker sideways than in its depth.
- **Tapered flanges:** bolting through the sloped flanges of C shapes needs bevelled washers so the nut sits square.

## Where C-channels are used

- Lintels and frames around openings in walls and decks
- Stair stringers and landing framing
- Bracing, struts and girts
- Mechanical dunnage and equipment supports
- Edge frames for pits, trenches and hatches
- Purlins and girts in pre-engineered buildings (cold-formed C sections)

## C-channel vs U-channel vs I-beam

"U-channel" usually means a lighter formed section with equal-height legs and a rounded profile, often in aluminum or thin steel, used for trim and guides rather than structure. An I-beam or W-shape has flanges on both sides of the web, so it is stronger and doesn't twist the same way, but it can't sit flat against a wall the way a channel can.

## Related terms

- [Hollow Steel Section (HSS)](https://essential.construction/academy/glossary/hollow-steel-section/)
- [Bent Plate](https://essential.construction/academy/glossary/bent-plate/)
- [Weld](https://essential.construction/academy/glossary/weld/)
- [Galvanize](https://essential.construction/academy/glossary/galvanize/)

## Related templates and guides

- [Guide to the design and construction of structural steel](https://essential.construction/academy/tutorials/the-ultimate-guide-to-the-design-and-construction-of-structural-steel/)
- [Hot rolling vs cold rolling of steel tubes](https://essential.construction/academy/tutorials/difference-between-hot-rolling-and-cold-rolling-of-square-and-rectangular-tubes/)
- [ANSI/AISC 360-16 Specification for Structural Steel Buildings (since updated to 360-22)](https://essential.construction/files/information/codes/ansi-360-16-specifications-for-structural-steel-buildings/)
- [Design Guide 09: Torsional Analysis of Structural Steel Members](https://essential.construction/files/information/guides/design-guide-09-torsional-analysis-of-structural-steel-members/)

## Frequently asked questions

### What is a C-channel used for in construction?

C-channels are used for lintels, stair stringers, bracing, framing around openings, equipment supports and edge frames. The flat back lets the member sit flush against a wall, slab edge or another member, and the open side makes connections easy.

### What does C8x11.5 mean?

It is a US American Standard Channel with a nominal depth of 8 inches that weighs 11.5 pounds per foot. Dimensions such as flange width and thicknesses for each size are listed in the AISC Steel Construction Manual and supplier charts.

### What is the difference between C and MC channel?

Both are hot-rolled channels. C shapes are the American Standard Channels; MC shapes are 'miscellaneous channels' with different flange proportions, often heavier for a given depth. They aren't interchangeable without checking the section properties.

### What is a PFC?

PFC stands for parallel flange channel, the standard hot-rolled channel in the UK. Unlike US C shapes, its flanges have parallel faces, and sizes are written as depth by flange width in millimetres and mass in kilograms per metre.
