
A bent plate is a flat steel plate that has been bent on a press brake into an angle or channel shape to form a structural or miscellaneous metals member. Bent plates are commonly used as slab edge pour stops, closures at openings, and supports for curtain wall or cladding.
How bent plates are made
The fabricator cuts plate to size and bends it cold on a press brake. Two things control how tight the bend can be: the plate thickness and grade, and the direction of the bend relative to the plate’s rolling direction (bending across the rolling direction is less likely to crack). The AISC Steel Construction Manual and plate producers publish recommended minimum inside radii. If the part will be hot-dip galvanized, tell the fabricator, because tight cold bends can raise the risk of embrittlement (ASTM A143 covers this).
Where bent plates are used
- Pour stops: a bent plate welded to the perimeter beam holds the concrete at the slab edge and sets where the edge ends up.
- Closures: at deck openings, shafts, stairs and changes in slab level.
- Facade support: edge members for curtain wall anchors, shelf angles and cladding supports where a rolled angle doesn’t fit.
- Skewed connections: a single bent plate can connect a beam framing in at an angle.
- Miscellaneous metals: lintels, stair stringers and pans, sill supports, canopy fascias and cover plates.
Bent plate vs angle
| Rolled angle | Bent plate | |
|---|---|---|
| Corner | Sharp outside heel, filleted inside | Radiused inside and out |
| Sizes | Standard leg lengths and thicknesses | Any leg length the brake can form |
| Angle | 90 degrees | Any angle, for slopes and skews |
| Shapes | L only | L, Z, channel, hat and multi-bend profiles |
| Cost | Usually cheaper for standard sizes | Extra fabrication, but saves splicing or welding up built shapes |
Use a rolled angle when a standard size works; specify a bent plate when you need an odd leg, an odd angle or a single piece with several bends.
How bent plates appear on drawings
Structural and misc metals drawings usually call them out as “BENT PL” with the thickness, leg dimensions, any angle other than 90 degrees, and the weld to the supporting member. Pour stop sizes are often given in a schedule tied to slab thickness and overhang.
Installation and inspection tips
- Survey the pour stop line before the pour. It sets the slab edge, and the curtain wall anchors depend on it.
- Check welds to the beam and any kickers or stiffeners that brace the pour stop against wet concrete.
- Look for cracking on the outside of bends.
- Touch up galvanizing or primer after field welding.
Related terms
Related templates and guides
- Guide to the design and construction of structural steel
- Design Guide 22: Facade Attachments to Steel-Framed Buildings
- ANSI/AISC 303-16 Code of Standard Practice (since updated to 303-22)
- Concrete Pre-Pour Checklist Template
Frequently asked questions
What is a bent plate in structural steel?
It is a steel plate bent on a press brake into an angle, channel or other profile. It does the job of a rolled shape where standard sizes or angles don’t fit, and is common in slab edges, closures, facade supports and miscellaneous metals.
What is a bent plate pour stop?
It is a bent steel plate welded along the edge of a steel beam to contain the concrete when a slab on metal deck is poured. The vertical leg sets the slab edge and thickness, and it is sized to the slab depth and overhang shown on the drawings.
Is a bent plate as strong as an angle?
It depends on thickness, grade and bend radius, not the name. A bent plate of the same steel and thickness behaves much like an angle, but the radiused corner changes the section slightly. The engineer sizes either one for the load.
Is it bent plate or bend plate?
Bent plate is the usual term on drawings, since the plate has been bent. ‘Bend plate’ is a common spelling in searches and on some sites, but it refers to the same item.
Ask AI about this page: ChatGPT, Claude or PerplexityCopy as Markdown
